RICOH ELECTRONIC DEVICES Co., Ltd. - Exhibitor press releases - electronica exhibitor directory

Exhibitor press releases

Ricoh launches LDO regulator with 0.3 µA current consumption and integrated battery voltage monitor

add to my favorites
print content

Ricoh launches LDO regulator with 0.3 µA current consumption and integrated battery voltage monitor

Osaka, Japan, 7 August 2018 – Ricoh Electronic Devices Co., Ltd. in Japan has launched the RP124, a 100mA LDO regulator with a unique integrated battery voltage monitor to make it possible to measure the remaining charge left in the battery.

The regulator features an ultra-low current consumption of only 0.3µA (at no-load), extending the lifetime of battery powered devices, which is important for those applications that are mainly in sleep mode and resume for a periodical brief moment to perform a task.

The additional battery monitor circuit is one of the key features of the RP124, a conventional way to measure the remaining battery charge is using an external resistor divider + MOSFET connected to an A/D Converter. However, the input impedance of this solution is typically low resulting in a considerable current flow to ground, draining the battery and limiting the lifetime of the application. The RP124 provides a simple solution with a built-in resistor divider and voltage follower as a buffer. As an advantage, this circuit has a much lower current flow to ground and the output is compatible with the input impedance of the A/D converter.  In addition, all essential components for this circuit are integrated into the chip, reducing valuable circuit board space and cost. In this way, it is possible to make a simple fuel gauge for primary batteries, for example.

Specific applications are mainly in a sleep mode and only wake up briefly to perform a measurement, transmits some data and go back to the sleep mode again. So actually, the sleep mode is the dominating operating mode and it is necessary to reduce the current consumption in this mode as much as possible. The RP124 fits perfectly in such requirement with its current consumption of 0.3µA. There are a few product versions available with options for the CE pin and the automatic discharge function. The CE pin disables the LDO for the B and D-versions. As for the E-version, it has the possibility to disable the battery monitor circuit when not in use. It saves another 0.1µA whilst the LDO remains in operation, resulting in a current consumption of only 0.2µA.

The RP124 (similar to the popular RP118 without battery voltage monitor) is a special kind of product offering three operating modes:
1.   Low power consumption mode, saving battery power at low output current demand
2.   Fast transient response mode, enhanced dynamic performance at high output current demand
3.   Off mode, to reduce current consumption to a minimum

The device switches automatically between the low power consumption and the fast transient response mode, based on the output current demand of the application. The performance of the LDO is enhanced in fast transient response mode. In particular, the ripple rejection as well as the response speed to line and load transients demonstrate better results compared to a conventional LDO with low current consumption. This means the RP124 contributes to optimised output voltage stability and ripple reduction. The Off Mode is controlled by the Chip Enable pin and turns the LDO offline, reducing current consumption to a minimum.

The RP124 features an embedded fold back current limit circuit. When a short circuit occurs at the output, this circuit will decrease the output current to a level of 65mA, thus protecting the LDO and other electronic parts of the application from possible damage. After removing the short, the regulator resumes to normal operation automatically.

Optional features by product version:
•   Package: standard SOT-23-5 or compact DFN1212-6 package to minimize the PCB area.
•   Resistor divider ratio: the battery monitor output provides 1/3 or 1/4 of the input voltage.
•   CE pin function: pin to disable the LDO Regulator or Voltage Monitor circuit.
•   Auto-discharge function: none, auto-discharge available for LDO Regulator or Voltage Monitor output. This function enables a fast discharge of the output capacitor when the LDO is switched off.

RP124 Features:
LDO Regulator
Input Voltage:
Output Voltage:
Output Voltage Accuracy:
Dropout Voltage:
Output Current:
Supply Current:
Protection Circuits:
Short Circuit Current Limit:
Output Capacitor:

Battery Monitor
Output Voltage
Supply Current
Output Capacitor
RP124N Package:
RP124L Package:
1.7 V to 5.5 V
(11 versions) 1.2 V to 3.6 V
(Iout=100 mA, 2.8 V type) Typ. 0.12 V
Min. 100 mA
(Iout=0 mA) Typ. 0.2 µA
Fold Back Current Limit
Typ. 65 mA
Ceramic, Min 1.0 µF

Optional, 1/3 Vin or 1/4 Vin
0.1 µA
0.1 µF to 0.22 µF
(L2.9 x W2.8 x H1.1 mm) SOT23-5
(L1.2 x W1.2 x H0.4 mm) DFN1212-6

For further information about our semiconductor products:
Visit or contact:
Ricoh Europe (Netherlands) B.V., Semiconductor Support Centre
Hans Adams, Manager
Tel: +31 20 5474 309

Our press contact

Ricoh Europe (Netherlands) B.V., Semiconductor Support Centre
Hans Adams, Manager
Tel: +31 20 5474 309

More exhibitor press releases:
Your favorites
Exhibitors (0)
Products (0)
Applications (0)
Product picture (0)
Press information (0)
Add your favorite entries.
Exhibitors of electronica 2018 present their electronica highlights and novelties!
Make new valuable contacts - it is easy and efficient!
APP Download
Your mobile trade fair guide - download the free electronica app to your tablet or smartphone!
Quick Links
This website uses cookies to ensure you get the best experience on our website.

More info
OK, got it